ASTM D5511 PDF

ASTM D is a standard test anaerobic biodegradation test method for determining anaerobic biodegradation of plastic materials under high-solids. ASTM D Standard Test Method. D Standard Test Method for Determining Anaerobic Biodegradation of Plastic Materials Under. High-Solids. ASTM D Significance and Use. Biodegradation of a plastic within a high- solids anaerobic digestion unit is an important phenomenon because it will affect .

Author: Doukree Faezragore
Country: Equatorial Guinea
Language: English (Spanish)
Genre: Photos
Published (Last): 23 May 2015
Pages: 301
PDF File Size: 5.97 Mb
ePub File Size: 7.3 Mb
ISBN: 647-8-68792-736-8
Downloads: 32455
Price: Free* [*Free Regsitration Required]
Uploader: Kagami

If the positive control which contains cellulose continues to exhibit biodegradation then the test is xstm valid and the inoculum considered alive.

The test materials are exposed to a methanogenic inoculum derived from anaerobic digesters operating only on pretreated household wstm. The vessels are airtight and are not exposed to UV radiation. Specific hazards are given in Section 8. When the test is run to satisfaction, final carbon and methane gas readings are recorded and the incubation vessels are emptied and the samples are cleaned and weighed.

Furthermore, results shall not be extrapolated past the actual duration of the test. Biodegradation of plastics could allow for the safe disposal of these plastics through aerobic and anaerobic solid-waste-treatment plants.

The test materials are exposed to a methanogenic inoculum derived from anaerobic digesters operating only on pretreated household waste.

Note 1—This test method is equivalent to ISO The test is allowed to run for as long as desired. This test method is designed to be applicable to all plastic materials that are not inhibitory to the microorganisms present in anaerobic digesters operating on household waste.

  BLUR KRISTEN MIDDLETON PDF

They are kept within awtm temperature and moisture tolerances. Three vessels are used for each sample, and one negative control and one positive control are prepared as well.

Link to Active This link will always route to the current Active version of the standard. Reports shall clearly state the percentage of net gaseous carbon generation for both the test and reference samples at the completion of the test.

Reports shall clearly state the percentage of net gaseous carbon generation for both the test and reference samples at the completion of the test.

ASTM D5511 – Anaerobic Biodegradation

Active view current version of standard. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as sstm of the standard.

ASTM D – Anaerobic Biodegradation | Situ Biosciences LLC

Placing the sample materials in an inoculum 5d511 from anaerobic digesters operating on household waste. However, it is expected to resemble the environment of a high-solids anaerobic-digestion process operated under optimum conditions. Historical Version s – ashm previous versions of standard. The molar weight of the total gas produced by the test samples is calculated and compared to the carbon weight of the original samples and the percent biodegradation of the samples can then be determined.

  LUTRON DW-6090 PDF

Specific hazards are given in Section 8. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

This inoculum contains methanogenic bacteria that are also found in landfills.

This test method also resembles other anaerobic conditions where the gas generated is recovered and biogas production is actively promoted by inoculation for example, codeposition of anaerobic sewage sludge, anaerobic leachate recirculationmoisture control for example, leachate recirculationand temperature atsm for example, short-term injection of oxygen, heating of recirculated leachate 5, 6, 7. The testing process includes: Link to Active This link will r5511 route to the current Active version of the standard.

The values given in SI units are to be regarded as the standard. Biodegradation of a plastic within a high-solids anaerobic digestion unit is an important phenomenon because it will affect the decomposition of other waste materials enclosed by the plastic and the resulting quality and appearance of the digestate after an anaerobic digestion process.

Furthermore, results shall not be extrapolated past the actual duration of the test. Placing the samples in incubation vessels after the inoculum is prepared. Then, the anaerobic bacteria begin to multiply and colonize in the vessel.