CC Texas Instruments RF Transceiver datasheet, inventory, & pricing. CC The CC is a low cost true single chip UHF transceiver designed for very low power wireless applications. The circuit is mainly intended for the ISM. Highly Integrated MultiCh RF Transceiver Designed for Low-Power Wireless Apps. Datasheet Texas Instruments CC
|Published (Last):||8 July 2016|
|PDF File Size:||12.33 Mb|
|ePub File Size:||14.20 Mb|
|Price:||Free* [*Free Regsitration Required]|
The digitally controlled oscillator DCO allows wake-up from low-power modes to active mode in less than 6ms. Figure 3-Incorrect Figure 4-Correct Solid ground plane below the IC and filter balun components Another important aspect of the filter balun layout is the ground plane.
A ccc1100 of the picture is reproduced below: Data is transferred serially through the 1-Wire protocol.
This microcontroller, an ultra-low-power bit RISC mixed-signal processor, is ideal for low power and portable applications. With a two-layer design, it becomes more complicated to achieve a solid ground. In designing circuits using their components, Texas Instruments’ website provides very helpful documentation and design examples.
This provides us with the ability to offer several options to our clients while using a consistent and proven transceiver architecture. The memory can be programmed 1 to bytes at a time, using the Page Program instruction.
By taking the time apply these techniques, hopefully, it will save you some layout mistakes and reworks, and thus reduce both development time and costs.
Filter Topology One of the key pieces of a design using the CC is the filter balun. Each page is bytes wide. Second it provides a low pass filter.
As with the filter balun section, the ground plane below the trace must be solid up to the antenna. For more information on the MCP linear charge management controller, the datasheet can be found at Microchip.
Datashet more datashee on the CC microcontroller, the datasheet can be found at TI. The CC also provides hardware support for packet handling, data buffering, burst transmissions, clear channel assessment, link quality indication, and wake-on-radio.
For more information on the M25P80 flash memory, the datasheet can be datashset at ST. Because of the importance and multi-tasking required by this portion of the design, there are some important considerations in layout that need to be taken into account.
Table of Contents 1. Conclusion This article, if read in conjunction with the excellent TI application notes for this chip, will make it easier to incorporate the CC into your design.
With extensive capabilities for packet datashdet, data buffering, burst transmissions, clear channel assessment, and link quality indication, this chip is typically used with an on-board microcontroller. This service is also offered in conjunction with Design Sources.
The design of the filter balun accomplishes three main tasks. In this case, if the width is wider than the component pads, the trace will have to be reduced just before entering the pad. First it converts the balanced RF signals from the CC into an unbalanced dtaasheet. The memory is organized as 16 sectors, each containing pages.
If this is not possible, the trace should be routed directly below the device, but NOT under the RF pads or filter balun. The current version for the CC is CC SSS Online is proud to present some tricks and hints on this important topic to help you design RF circuits that don’t fall prey to datashret harmonics, drop out and other bugaboos that can haunt the designer.
Design and layout is an art form, and never more so than when you are designing an RF circuit. Layout Resources on the Web. While the advice presented here may seem simple, failure to apply these techniques may result in a circuit that does not perform as desired.
Hardcover – pages July Because the CC packaging has pins on all four sides, it can be difficult catasheet connect things such as power. This will cause the trace for the second inductor to be longer cc110 more bending.
CC Datasheet, PDF – Alldatasheet
It is often necessary to switch between layers in order access all of the connections required. The newest version of this chip, the CC, has been recently introduced and is the chip we are using in new designs.
The RF transceiver is integrated with a configurable baseband modem. The complete file can be obtained from the worldsens web site. The balanced portion of the filter balun is very susceptible to variations between the two sections. The current design has improvements to eliminate harmonic emission as well as variations based on power settings.