Gocycle GS – Owner’s Manual (EN) – English. Tom. 4 months ago; Updated. Follow. Download the latest Gocycle GS Owner’s Manual. Gocycle GS Owners. Technical Bulletins, Owner’s Manuals and Documentation. GreenMiles is your Official Gocycle Partner for the Benelux. To meet the growing demand for mobility in and between urban areas, GreenMiles is convinced that.
|Published (Last):||26 January 2006|
|PDF File Size:||20.74 Mb|
|ePub File Size:||8.58 Mb|
|Price:||Free* [*Free Regsitration Required]|
Battery Pack Disposal When your Gocycle lithium battery has reached the end of its service life, you must recycle or dispose of it properly: Don’t have an account? Cleaning And Preventing Corrosion Cleaning and Preventing Corrosion We do not recommend that you ride your Gocycle in heavy rain or store it in damp or wet areas.
During riding when using the motor, the battery charge level will decrease over time, with fewer LEDs displayed accordingly.
Table of Contents Add to my manuals Add. How do I register the Gocycle and gain normal operation?
Gocycle User Manual & FAQ
Comments to this Manuals Your Name. Check the hub gear bearing adjustment every miles km or 6 months. No, it’s not necessary. As with all hydraulic brakes, for the mznual possible performance, we recommend that the hydraulic brakes on your Gocycle are bled every 12 months. To install the rear reflector: It is considered normal to slightly heat the battery when traveling.
Gocycle G3 Owner’s Manual
Failure to inspect the hub gear bearing adjustment may have serious consequences and could result in serious bodily injury or even death. This indicator is available on the built-in bicycle display. Where is gocycls battery located? Warranty Registration For your continued satisfaction and safety whilst riding your Gocycle, we strongly encourage you to register your Gocycle with us. Like all lithium-ion batteries, you can recharge it to full charge.
Gocycle User Manual & FAQ – Service & Repair Manuals
By choosing to ride a Gocycle, you assume the responsibility for these risks, and it is important that you know how to ride responsibly and to exercise proper maintenance to minimise such risks and potential damage. To do this, clean the Gocycle thoroughly with a damp maual.
Such changes are temporary. Extreme caution should be used when attempting to touch any part of the motor after it has been in operation—the tocycle caution you would gochcle in the kitchen with hot pots or pans or Do not attempt to ride your Gocycle without re-installing the brake pads and securing split pin.
Diagnosis Modes Your Gocycle is pre-programmed with a number of modes to assist in fault diagnosis, should an issue occur.
When the tread depth is critically low and the centreline grooves in the tyre have worn down in any part of the tyre, it may be dangerous to continue to ride on the tyre, and in this event, we recommend that you replace the tyre.
Pinch both brake pads and remove from the calliper. If the battery is not in Operation Mode, the Gocycle will not function, the gears will not shift and the motor will not work.
The closing resistance should act over the remaining 60 degrees of movement till it is firmly shut in the correct location. Will the battery warm up? Keep 2 cam levers in the closed position and open one cam lever fully so that the back edge touches the next closed cam lever.
Lightly move the cam lever back and forth to gauge the extent of the free play. Warranty Warranty Registration For your continued satisfaction and safety whilst riding your Gocycle, we strongly encourage you to register your Gocycle with us. Apply pressure onto the right hand side of the Snap Rail Tool Holder B until this side is properly located onto the right saddle rail.
Do not leave the Gocycle on charge for more than 24 hours. Rotate the rear wheel. Tighten to a torque of 3—4Nm. Remove the three black rubber grommets as indicated by the arrows.
The battery will enter Sleep Mode automatically if not in use for 5 hours. If the Gocycle is plugged into mxnual charger and the charger is charging, it will never enter Sleep Mode.